16Generation

Miller index

From Wikipedia, the free encyclopedia

Jump to: navigation, search

Planes with different Miller indices in cubic crystals

Examples of directions

Miller indices form a notation system in crystallography for planes in crystal (Bravais) lattices.

In particular, a family of lattice planes is determined by three integers h, k, and ℓ, the Miller indices. They are written (hkℓ), and each index denotes a plane orthogonal to a direction (h, k, ℓ) in the basis of the reciprocal lattice vectors. By convention, negative integers are written with a bar, as in 3 for −3. The integers are usually written in lowest terms, i.e. their greatest common divisor should be 1. Miller index 100 represents a plane orthogonal to direction h; index 010 represents a plane orthogonal to direction k, and index 001 represents a plane orthogonal to ℓ.

There are also several related notations:^[1]

the notation {hkℓ} denotes the set of all planes that are equivalent to (hkℓ) by the symmetry of the lattice.

In the context of crystal directions (not planes), the corresponding notations are:

[hkℓ], with square instead of round brackets, denotes a direction in the basis of the direct lattice vectors instead of the reciprocal lattice; and
similarly, the notation $Description: \left\langle hk\ell\right\rangle$ denotes the set of all directions that are equivalent to [hkℓ] by symmetry.

Miller indices were introduced in 1839 by the British mineralogist William Hallowes Miller. The method was also historically known as the Millerian system, and the indices as Millerian,^[2] although this is now rare.

The Miller indices are defined with respect to any choice of unit cell and not only with respect to primitive basis vectors, as is sometimes stated.

Contents

Definition

Examples of determining indices for a plane using intercepts with axes; left (111), right (221)

There are two equivalent ways to define the meaning of the Miller indices:^[1] via a point in the reciprocal lattice, or as the inverse intercepts along the lattice vectors. Both definitions are given below. In either case, one needs to choose the three lattice vectors a₁, a₂, and a₃ that define the unit cell (note that the conventional unit cell may be larger than the primitive cell of the Bravais lattice, as the examples below illustrate). Given these, the three primitive reciprocal lattice vectors are also determined (denoted b₁, b₂, and b₃).

Then, given the three Miller indices h, k, ℓ, (hkℓ) denotes planes orthogonal to the reciprocal lattice vector:

$Description: \mathbf{g}_{hk\ell} = h \mathbf{b}_1 + k \mathbf{b}_2 + \ell \mathbf{b}_3 .$

That is, (hkℓ) simply indicates a normal to the planes in the basis of the primitive reciprocal lattice vectors. Because the coordinates are integers, this normal is itself always a reciprocal lattice vector. The requirement of lowest terms means that it is the shortest reciprocal lattice vector in the given direction.

Equivalently, (hkℓ) denotes a plane that intercepts the three points a₁/h, a₂/k, and a₃/ℓ, or some multiple thereof. That is, the Miller indices are proportional to the inverses of the intercepts of the plane, in the basis of the lattice vectors. If one of the indices is zero, it means that the planes do not intersect that axis (the intercept is "at infinity").

Considering only (hkℓ) planes intersecting one or more lattice points (the lattice planes), the perpendicular distance d between adjacent lattice planes is related to the (shortest) reciprocal lattice vector orthogonal to the planes by the formula: $Description: d = 2\pi / |\mathbf{g}_{h k \ell}|$ .^[1]

The related notation [hkℓ] denotes the direction:

$Description: h \mathbf{a}_1 + k \mathbf{a}_2 + \ell \mathbf{a}_3 .$

That is, it uses the direct lattice basis instead of the reciprocal lattice. Note that [hkℓ] is not generally normal to the (hkℓ) planes, except in a cubic lattice as described below.

Case of cubic structures

For the special case of simple cubic crystals, the lattice vectors are orthogonal and of equal length (usually denoted a); similar to the reciprocal lattice. Thus, in this common case, the Miller indices (hkℓ) and [hkℓ] both simply denote normals/directions in Cartesian coordinates.

For cubic crystals with lattice constant a, the spacing d between adjacent (hkℓ) lattice planes is (from above):

$Description: d_{hk \ell}= \frac {a} { \sqrt{h^2 + k^2 + \ell ^2} }$ .

Because of the symmetry of cubic crystals, it is possible to change the place and sign of the integers and have equivalent directions and planes:

Coordinates in angle brackets such as ⟨100⟩ denote a family of directions which are equivalent due to symmetry operations, such as [100], [010], [001] or the negative of any of those directions.
Coordinates in curly brackets or braces such as {100} denote a family of plane normals which are equivalent due to symmetry operations, much the way angle brackets denote a family of directions.

For face-centered cubic and body-centered cubic lattices, the primitive lattice vectors are not orthogonal. However, in these cases the Miller indices are conventionally defined relative to the lattice vectors of the cubic supercell and hence are again simply the Cartesian directions.

Case of hexagonal and rhombohedral structures

Description: http://upload.wikimedia.org/wikipedia/commons/thumb/8/82/Indices_miller_bravais.png/220px-Indices_miller_bravais.png

Miller-Bravais indices

With hexagonal and rhombohedral lattice systems, it is possible to use the Bravais-Miller index which has 4 numbers (h k i ℓ)

i = −(h + k).

Here h, k and ℓ are identical to the Miller index, and i is a redundant index.

This four-index scheme for labeling planes in a hexagonal lattice makes permutation symmetries apparent. For example, the similarity between (110) ≡ (1120) and (120) ≡ (1210) is more obvious when the redundant index is shown.

In the figure at right, the (001) plane has a 3-fold symmetry: it remains unchanged by a rotation of 1/3 (2π/3 rad, 120°). The [100], [010] and the [110] directions are really similar. If S is the intercept of the plane with the [110] axis, then

i = 1/S.

There are also ad hoc schemes (e.g. in the transmission electron microscopy literature) for indexing hexagonal lattice vectors (rather than reciprocal lattice vectors or planes) with four indices. However they don't operate by similarly adding a redundant index to the regular three-index set.

For example, the reciprocal lattice vector (hkℓ) as suggested above can be written as ha*+kb*+ℓc*if the reciprocal-lattice basis-vectors are a*, b*, and c*. For hexagonal crystals this may be expressed in terms of direct-lattice basis-vectors a, b and c as

$Description: (hk\ell) = h\vec{a^*} + k\vec{b^*} + \ell \vec{c^*}= \frac{2}{3 a^2}(2 h + k)\vec{a} + \frac{2}{3 a^2}(h+2k)\vec{b} + \frac{1}{c^2} (\ell) \vec{c}.$

Hence zone indices of the direction perpendicular to plane (hkℓ) are, in suitably normalized triplet form, simply [2h+k,h+2k,ℓ(3/2)(a/c)²]. When four indices are used for the zone normal to plane (hkℓ), however, the literature often uses [h,k,-h-k,ℓ(3/2)(a/c)²] instead.^[3] Thus as you can see, four-index zone indices in square or angle brackets sometimes mix a single direct-lattice index on the right with reciprocal-lattice indices (normally in round or curly brackets) on the left.

The crystallographic planes and directions

Description: http://upload.wikimedia.org/wikipedia/commons/thumb/6/6c/Cristal_densite_surface.svg/220px-Cristal_densite_surface.svg.png

Dense crystallographic planes

The crystallographic directions are fictitious lines linking nodes (atoms, ions or molecules) of a crystal. Similarly, the crystallographic planes are fictitious planes linking nodes. Some directions and planes have a higher density of nodes; these dense planes have an influence on the behaviour of the crystal:

optical properties: in condensed matter, the light "jumps" from one atom to the other with the Rayleigh scattering; the velocity of light thus varies according to the directions, whether the atoms are close or far; this gives the birefringence
adsorption and reactivity: the adsorption and the chemical reactions occur on atoms or molecules, these phenomena are thus sensitive to the density of nodes;
surface tension: the condensation of a material means that the atoms, ions or molecules are more stable if they are surrounded by other similar species; the surface tension of an interface thus varies according to the density on the surface

the pores and crystallites tend to have straight grain boundaries following dense planes
cleavage

dislocations (plastic deformation)

the dislocation core tends to spread on dense planes (the elastic perturbation is "diluted"); this reduces the friction (Peierls–Nabarro force), the sliding occurs more frequently on dense planes;
the perturbation carried by the dislocation (Burgers vector) is along a dense direction: the shift of one node in a dense direction is a lesser distortion;
the dislocation line tends to follow a dense direction, the dislocation line is often a straight line, a dislocation loop is often a polygon.

For all these reasons, it is important to determine the planes and thus to have a notation system.

Integer vs. irrational Miller indices: Lattice planes and quasicrystals

Ordinarily, Miller indices are always integers by definition, and this constraint is physically significant. To understand this, suppose that we allow a plane (abc) where the Miller "indices" a, b and c (defined as above) are not necessarily integers.

If a, b and c have rational ratios, then the same family of planes can be written in terms of integer indices (hkℓ) by scaling a, b and c appropriately: divide by the largest of the three numbers, and then multiply by the least common denominator. Thus, integer Miller indices implicitly include indices with all rational ratios. The reason why planes where the components (in the reciprocal-lattice basis) have rational ratios are of special interest is that these are the lattice planes: they are the only planes whose intersections with the crystal are 2d-periodic.

For a plane (abc) where a, b and c have irrational ratios, on the other hand, the intersection of the plane with the crystal is not periodic. It forms an aperiodic pattern known as a quasicrystal. This construction corresponds precisely to the standard "cut-and-project" method of defining a quasicrystal, using a plane with irrational-ratio Miller indices. (Although many quasicrystals, such as the Penrose tiling, are formed by "cuts" of periodic lattices in more than three dimensions, involving the intersection of more than one such hyperplane.)

See also

References

^ Jump up to: ^a ^b ^c Neil W. Ashcroft and N. David Mermin, Solid State Physics (Harcourt: New York, 1976)
Jump up ^ Oxford English Dictionary Online (Consulted May 2007)
Jump up ^ J. W. Edington (1976) Practical electron microscopy in materials science (N. V. Philips' Gloeilampenfabrieken, Eindhoven) ISBN 1-878907-35-2, Appendix 2